[fibosearch]

Write what you are looking for and press enter to begin your search!

[fibosearch]

0

No products in the cart.

Cart Total

Sign In

Wheel bearing specialist

Wheel bearings in Torrevieja: ultrasonic clean, the right grease

I clean every bearing inside out in an ultrasonic bath and grease it to suit your riding: a light low-friction grease for maximum speed, or a water-resistant grease that lasts longer in rain, dust and coastal salt air. 10 years as a professional bike mechanic.

10+
years as a professional mechanic
Ultrasonic
cleaned right into the races
2 greases
speed or durability
100+
official certifications

Why ultrasonic

Clean inside, not just outside.

  • Reaches where a brush can’t

    Cavitation in the ultrasonic bath lifts old grease, dust and grit out of the races, balls and cage.

  • No dirt pushed deeper

    A spray or a jet of water pushes dirt further in. The bath draws it out and leaves it at the bottom of the tank.

  • A real diagnosis

    Once the bearing is clean you can feel whether it spins smoothly or has rough spots, play or rust. I only replace what is damaged.

How I work

Six steps, wheel by wheel.

  1. Diagnosis

    I turn the axle by hand and check each wheel for play, roughness and noise.

  2. Careful strip-down

    I open the hub with its brand’s tools. If bearings have to come out, I use a puller, never a hammer.

  3. Ultrasonic bath

    I lift the seals off without bending them and the bearing spends about 30 minutes in the bath with degreaser.

  4. Dry & inspect

    Rinsed, air-dried and checked: it must spin smoothly, with no rough spots or rust.

  5. Right grease, right amount

    Speed or durability grease to suit your riding, in the right amount: too much grease slows you down too.

  6. Fit & adjust

    Pressed in square, preload set with no play and no extra pressure, then the wheel is tested.

Grease makes the difference

Speed or durability?

You choose the goal when you book. Not sure? I’ll advise you based on your bike and how you ride.

Maximum speedMaximum durability
GreaseLight, low-viscosity, low-frictionWater-resistant and thicker: stands up to water and salt
AmountJust enough, for the lowest dragFuller, to seal out water, dust and salt
Best forRoad, time trial, triathlon and race daysMTB, gravel, daily riding, rain and coastal rides
ServicingMore often: each season or before a key raceLess often: more kilometres between services

CeramicSpeed bearings: warranty kept

On CeramicSpeed bearings I only use original CeramicSpeed grease and the amount the brand recommends, so your warranty stays valid.

Need new bearings?

If a bearing is worn or you want an upgrade, I can order ceramic bearings or good-quality steel bearings for your hub and fit them.

Ask for bearings on WhatsApp →

Prices

Clear prices, from.

VAT included. If a bearing is damaged I’ll give you the price before replacing it. Labour is cheaper for bikes bought in my shop.

Book a service
  • Wheel bearings: ultrasonic clean & regreasePrice per wheel. Speed or durability grease.from €40 / wheel€22 · bike from my shop
  • Premium hub serviceDT Swiss, Industry Nine: ratchet clean and specific lube.from €80€45 · bike from my shop
  • Pivot bearing service (ultrasonic)Price per bearing. Ultrasonic clean and marine grease.from €16€9 · bike from my shop
  • Bottom bracket: service or replaceThreaded or press-fit, creak-free.from €60€33 · bike from my shop
  • Headset bearing replacementNew bearings and adjustment. Bearings extra.from €75€40 · bike from my shop

When to service

Signs your bearings need attention.

  • RoughnessTurning the axle by hand feels rough or notchy.
  • NoiseThe wheel rumbles or grinds as it rolls.
  • PlayYou can rock the rim side to side and feel movement at the hub.
  • Water, mud or beachAfter rain, mud, sand or washing the bike with a pressure washer.
  • Before racingBefore a key event, when every watt counts.
  • As a guideOnce a year on the road; more often for MTB, wet riding or near the sea.

Why me

Workshop work, not a spray can.

Mechanic and racer

I have raced marathon MTB since 2008. I know how a free-spinning hub feels, and what a dragging one costs you.

Official training

Training by the official SRAM service centre for Spain and Portugal, 100+ certifications and the 2017 Shimano T.E.C. award.

The right tools

Ultrasonic bath, presses and pullers for each hub, and the right grease for each use. I tell you what I found and what I did.

FAQ

Is it worth cleaning bearings, or should I replace them?

If the races and balls are healthy, a bearing that has been ultrasonically cleaned and properly greased spins smoothly again and you save the cost of a new one. If it has play, pitting or rust it needs replacing, and I’ll give you the price first.

Which grease is fastest?

A light low-friction grease, in the right amount. It spins with less resistance but protects less against water, so it needs checking more often. For daily riding, rain or MTB, a water-resistant grease is the better choice.

Are ceramic bearings faster?

They can roll a little more freely, but much of a bearing’s friction comes from the seals and the grease. A clean, well-greased steel bearing usually makes more difference than a dirty ceramic one or one with the wrong grease. I clean and grease ceramic bearings too.

Do I keep the warranty on my CeramicSpeed bearings?

On CeramicSpeed bearings I only use original CeramicSpeed grease and the amount of grease the brand recommends, so your warranty stays valid.

Can you get me new bearings?

Yes. If you want new ceramic bearings or good-quality steel bearings, I order them for your hub and fit them. Send me your wheel model and I’ll give you a price.

Why does living by the sea matter?

In Torrevieja the air carries moisture and salt, which work their way into bearings and rust them. That’s why I recommend water-resistant grease for everyday riding here, and not pressure-washing your hubs.

Do you work on all hub types?

Yes: cartridge-bearing hubs (such as DT Swiss or Industry Nine) and cup-and-cone hubs (such as many Shimano hubs), which I clean, grease and adjust. If your hub needs a special tool, send me the model.

How long does it take?

The bearings spend about 30 minutes in the ultrasonic bath, plus the strip-down, drying, greasing and refitting. Allow about 1 hour for one wheel and 1 h 30 min for a pair. By appointment, you usually get them back the same day.

Wheels not spinning like they used to?

Book online in a minute or WhatsApp me your wheel model.

See all services → · Suspension specialist →